Price & Ordering: The Faktum "W" Models

Traditional Faktum Cabinet Doors For Knobs and Handles

  • On this page we list our traditional cupboard doors and fronts for knobs and handles. The “W” models.
  • The fronts works fine with a Push Open solution or may be retrofitted with knobs or pull-handles. Will be pre-drilled from the factory for hinges and for drawers and just like with fronts from IKEA the drillings for the specific pull handles are always made on site by the end user.
  • These fronts are for the Faktum kitchen range that was discontinued from the IKEA warehouses back in 2013. Keep the kitchen you already own. Just replace the fronts!
  • The fronts will be made in the correct size by IKEA´s original drawings and pre drilled by IKEAs templates. They will all fit perfectly out of the box just as if they were picked up from the local IKEA warehouse.
  • Before placing an order you may want to request a kit of our free color swatches? Please see the Free Colour Samples tab at the top menu of this page.
  • All the fronts on this page are priced by their size, not by the selected colour nor by the model. A shaker door is priced the same as a fully flat door in the same size. The chosen model + colour will show in the cart at €0.
  • This page may be utilised to price your project. Please just add all the needed sizes of the fronts into a cart and the system will calculate the total cost automatically. At the Checkout page you may finalize your order or save your cart for later.
  • On this page we list our traditional cupboard doors and fronts for knobs and handles. The “W” models.
  • The fronts works fine with a Push Open solution or may be retrofitted with knobs or pull-handles. Will be pre-drilled from the factory for hinges and for drawers and just like with fronts from IKEA the drillings for the specific pull handles are always made on site by the end user.
  • These fronts are for the Faktum kitchen range that was discontinued from the IKEA warehouses back in 2013. Keep the kitchen you already own. Just replace the fronts!
  • The fronts will be made in the correct size by IKEA´s original drawings and pre drilled by IKEAs templates. They will all fit perfectly out of the box just as if they were picked up from the local IKEA warehouse.
  • Before placing an order you may want to request a kit of our free color swatches? Please see the Free Colour Samples tab at the top menu of this page.
  • All the fronts on this page are priced by their size, not by the selected colour nor by the model. A shaker door is priced the same as a fully flat door in the same size. The chosen model + colour will show in the cart at €0.
  • This page may be utilised to price your project. Please just add all the needed sizes of the fronts into a cart and the system will calculate the total cost automatically. At the Checkout page you may finalize your order or save your cart for later.
  •  

Step #1: Choose Colour & Profile For The Fronts Here

Please start off the ordering process by selecting your preferred Colour and Pattern combination for your new fronts. The selected colour will apply to all the fronts in the same cart.

Colour Selector

Once a colour + profile is selected please continue further down this page to add some fronts to the same cart. They will all be made in the chosen colour.

Regular doors (Design W30) that have been retrofitted with pull-handles.

STEP #2: DRAWER FRONTS

Add some drawer fronts to the cart. Will be made in the chosen colour from Step #1 above. The fronts are prices by the size, not by the colour. Listed in tabs by the outside width of the cabinet they are intended to be fitted to. Just like IKEA we make the fronts a few millimeter smaller compared to the width of the cabinet so they are possible to open and close properly. In fact they will be manuafactured to the correct size by IKEAs original drawings and pre-drilled for the original IKEA Rationell drawers according to IKEAs original templates. 

These new drawer fronts will fit in a 30 cm wide cabinet. Please use the format Width x Height (not vice versa).

FOR 30 CM WIDE CABINETSSize in mmVAT Incl.
Drawer Front Faktum 30×13295×12637,00 
Drawer Front Faktum 30×18295×18243,00 
Drawer Front Faktum 30×25295×25457,00 
Drawer Front Faktum 30×31295×31063,00 
Drawer Front Faktum 30×57295×56687,00 
Drawer Front Faktum 30×70295×69493,00 

These new drawer fronts will fit in a 40 cm wide cabinet. Please use the format Width x Height (not vice versa).

FOR 40 CM WIDE CABINETSSize in mmVAT Incl.
Drawer Front Faktum 40×13395×12639,00 
Drawer Front Faktum 40×18395×18247,00 
Drawer Front Faktum 40×25395×25459,00 
Drawer Front Faktum 40×31395×31063,00 
Drawer Front Faktum 40×57395×56689,00 
Drawer Front Faktum 40×70395×69499,00 

These new drawer fronts will fit in a 45 cm wide cabinet. Please use the format Width x Height (not vice versa).

FOR 45 CM WIDE CABINETSSize in mmVAT Incl.
Drawer Front Faktum 45×13445×12643,00 
Drawer Front Faktum 45×18445×18249,00 
Drawer Front Faktum 45×25445×25463,00 
Drawer Front Faktum 45×31445×31069,00 
Drawer Front Faktum 45×57445×56699,00 
Drawer Front Faktum 45×70445×694119,00 

These new drawer fronts will fit in a 50 cm wide cabinet. Please use the format Width x Height (not vice versa).

FOR 50 CM WIDE CABINETSSize in mmVAT Incl.
Drawer Front Faktum 50×13495×12643,00 
Drawer Front Faktum 50×18495×18249,00 
Drawer Front Faktum 50×25495×25463,00 
Drawer Front Faktum 50×31495×31069,00 
Drawer Front Faktum 50×57495×56699,00 
Drawer Front Faktum 50×70495×694119,00 

These new drawer fronts will fit in a 60 cm wide cabinet. Please use the format Width x Height (not vice versa).

FOR 60 CM WIDE CABINETSSize in mmVAT Incl.
Drawer Front Faktum 60×9595×9439,00 
Drawer Front Faktum 60×13595×12643,00 
Drawer Front Faktum 60×18595×18249,00 
Drawer Front Faktum 60×25595×25463,00 
Drawer Front Faktum 60×31595×31069,00 
Drawer Front Faktum 60×57595×56699,00 
Drawer Front Faktum 60×70595×694119,00 

These new drawer fronts will fit in a 80 cm wide cabinet. Please use the format Width x Height (not vice versa).

FOR 80 CM WIDE CABINETSSize in mmVAT Incl.
Drawer Front Faktum 80×13795×12659,00 
Drawer Front Faktum 80×18795×18269,00 
Drawer Front Faktum 80×25795×25473,00 
Drawer Front Faktum 80×31795×31079,00 
Drawer Front Faktum 80×57795×566107,00 

These fronts are intended for integrated dishwashers. The only difference compared to regular doors or drawer fronts are the drillings. Since the front is fitted to the dishwasher door via the fittings supplied with the washer there is no need for pre-drilled holes for hinges since those holes will be left empty anyway. And an empty hole might take in moisture and ruin the front from behind. Please refer to the fitting manual that was supplied with the dishwasher on how to fit the front to your specific dishwasher. Please use the format Width x Height (not vice versa).

NameSize in mmVAT Incl.
Dish-front 45×57445×56699,00 
Dish-front 45×70445×69499,00 
Dish-front 50×70495×694119,00 
Dish-front 60×57595×56699,00 
Dish-front 60×70595×694119,00 

STEP #3: DOORS

Add some doors to the cart. Will be made in the chosen colour from Step #1 above. The fronts are prices by the size, not by the colour. Listed in tabs by the outside width of the cabinet they are intended to be fitted to. Just like IKEA we make the fronts a few millimeter smaller compared to the width of the cabinet so they are possible to open and close properly. In fact they will be manuafactured to the correct size by IKEAs original drawings and pre-drilled for the original IKEA FAktum hinges according to IKEAs original templates. 

These new doors will fit in a 15 or 20 cm wide cabinet. Please use the format Width x Height (not vice versa).

FOR 15-20 CM WIDE CABINETSSize in mmVAT Incl.
Door Faktum 15×70146×69483,00 
Door Faktum 20×70196×69489,00 
Door Faktum 20×92196×918119,00 

These new doors will fit in a 30 cm wide cabinet. Please use the format Width x Height (not vice versa).

FOR 30 CM WIDE CABINETSSize in mmNoteVAT Incl.
Door Faktum 30×57296×566

 

87,00 
Door Faktum 30×70296×694

Not for a corner cabinet

93,00 
Folding Door Faktum 30×70 A296×694

For a 90° base corner. Both the A+B doors must be ordered.

 

97,00 
Folding Door Faktum 30×70 B296×694

For a 90° base corner. Both the A+B doors must be ordered.

97,00 
Door Faktum 30×92296×918

This door will not fit a 45° corner cabinet.

129,00 

FOR WALL CORNER CABINETSSize in mmNoteVAT Incl.
Door Faktum 32×70317×694

Door for a wall corner cabinet. 45° angle.

93,00 
Door Faktum 32×92317×918

Door for a wall corner cabinet. 45° angle.

129,00 

These new doors will fit in a 40 cm wide cabinet. Please use the format Width x Height (not vice versa).

DOORS FOR 40 CM WIDE CABINETSSize in mmVAT Incl.
Door Faktum 40×57396×56689,00 
Door Faktum 40×70396×69499,00 
Door Faktum 40×92396×918139,00 
 

FOR TALL CABINETS – WIDTH 40 CMSize in mmVAT Incl.
Front Faktum 40×125395×1245199,00 Options
Door Faktum 40×195396×1942249,00 Options

These new doors will fit in a 45 cm wide cabinet. Please use the format Width x Height (not vice versa).

DOORS FOR 45 CM WIDE CABINETSSize in mmVAT Incl.
Door Faktum 45×70446×694119,00 
Door Faktum 45×92446×918149,00 
Fronts for dishwashers and washing machines are listed among the drawer fronts (Step #2 above).

These new doors will fit in a 50 cm wide cabinet. Please use the format Width x Height (not vice versa).

DOORS FOR 50 CM WIDE CABINETSSize in mmVAT Incl.
Door Faktum 50×57496×56699,00 
Door Faktum 50×70496×694119,00 
Door Faktum 50×92496×918149,00 
 
FOR TALL CABINETS – WIDTH 50 CMSize in mmVAT Incl.
Front Faktum 50×125495×1245199,00 Options
Door Faktum 50×195496×1942259,00 Options

These new doors will fit in a 60 cm wide cabinet. Please use the format Width x Height (not vice versa).

DOORS FOR 60 CM WIDE CABINETSSize in mmVAT Incl.
Door Faktum 60×35596×34273,00 
Door Faktum 60×57596×56699,00 
Door Faktum 60×70596×694119,00 
Door Faktum 60×92596×918149,00 

FOR TALL CABINETS – WIDTH 60 CMSize in mmVAT Incl.
Door Faktum 60×90596×900149,00 Options
Front Faktum 60×125595×1245199,00 Options
Door Faktum 60×195596×1942259,00 Options

Please use the format Width x Height (not vice versa). The horizontal doors will be pre-drilled for the hinges along the first figure (the width).

NameSize in mmVAT Incl.
Horizontal Door 70×30694×29693,00 
Horizontal Door 70×40694×39699,00 
Horizontal Door 92×30918×296129,00 
Horizontal Door 92×40918×396139,00 

Step #4: Side Panels and Plinths etc

Step #5: SoftClosing Hinges for Faktum

You may keep your existing Faktum hinges. But perhaps you would like to upgrade them as well to the modern and luxurious new hinges with SoftClose and SelfClose Technology built in. After all the old hinges must be removed from the old doors anyway. So now is a good time to upgrade!

ImageHinges for regular Faktum doorsPriceMore info
Hinge for Faktum (SoftClose + SelfClose)
Hinge for Faktum (SoftClose + SelfClose)12,00 Options
Hinges for Faktum. SoftClose + SelfClose, Multipack
Hinges for Faktum. SoftClose + SelfClose, Multipack Original price was: 12,00 €.Current price is: 9,90 €.Options
Mounting plate for an IKEA Faktum hinge
Mounting plate for the hinges5,00 Options

Step #6: Cabinets, Drawers and Shelves for Faktum kitchens

New Cabinets and Cupboards for your IKEA Faktum Kitchen project. We also list Shelves and Drawers etc for Faktum.

New drawers for IKEA Faktum and Rationell kitchens

Step #7: Doors and Fronts for IKEA Metod Kitchens

Yes, we also offer our premium doors and fronts for the Metod kitchen system currently sold by IKEA. Perhaps you would like to mix some new Metod doors into your existing Faktum kitchen? Please just continue and add Metod sized doors and fronts into your cart. Will be made in the same pattern + colour combination as the Faktum doors in the same cart.

Item added to cart.
0 items - 0,00 

Left or Right Hinged?

The reason why we do not ask about Left or Right is because these doors are symetric. They will look the same no matter if they are reversed up-side-down. Therefore these doors are possible to be hung with the pre-drilled hinge holes either to the left or to the right and you will not be able to tell the difference as there is no “up” or “down” on a symetric surface.

W11-DM2448-California-Oak-PT5000-Easy-Grey-16-9-1.jpg

Will The Fronts Be Pre-Drilled?

Yes. All the new doors will be pre-drilled with a perfect fit for IKEA hinges and all the new drawer fronts will be pre-drilled with a perfect fit for IKEA drawers.

Just like at IKEA we only drill holes for hinges and for drawer fitting. Not for knobs nor handles. Those drillings are always made on site and after all the new fronts are already fitted and aligned to each other. As an alternative perhaps you would like to have a look at our range of doors and fronts with Integrated Grips. The U12 handleless doors.

Regarding the drillings of the holes for knobs and handles we recomend the “Fixa” Drill Template from IKEA. This handy template helps you align and mark the position of the drill holes for precision mounting of knobs and handles. Simply search for part number 903.233.93 on the IKEA website in your country.